Re: Debian on iomega storcenter ix4-200d: succes!

Sorry, i came back after loong time.

I've finally setup my USB key with rootfs, as explained in http://forum.doozan.com/read.php?2,12096 , but i've not understood how to boot from it.

Seems to me that i've to modify my environment, but i've not understood how.

My current environment is:

Marvell>> printenv
bootdelay=1
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
run_diag=yes
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x000a0000(param),32m@0x0(flash) 
uboot_start=0x0
uboot_size=0xa0000
env_start=0xa0000
env_size=0x10000
kernel_start=0xb0000
kernel_size=0x228000
initrd_size=0x300000
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash);
flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_size);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000000;
bootcmd=run flash_load;
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000;
ethmtu=1500
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
uboot_ver=v1.1.1
ethact=egiga0
mfgmodel=ix4
fw_ver=v1_0_11_30938744
preroot_ver=0.1.5
serial_number=5560Y01011G113002C4J0I1
ethaddr=00:D0:B8:13:59:6B
serialno=EUB14047A1
modelname=31962600
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
initrd_start=0x2d8000
disaMvPnp=no
eth1addr=00:d0:b8:13:59:6c
enaAutoRecovery=yes
pcieTune=no

Environment size: 1843/16380 bytes

I've tried to use the 'usbboot' command, without success.

Sorry, please help me... thanks.